Hello RP's,
The RP system has to have a reasonable cost of ownership to be successful.
If the build process of a RP system has to be based on a built in scanner
to receive accurate, reliable and consistent parts, this RP system has no
chance on the market.
The problem comes if the part is removed from the RP system, has to fit
into the existing assembly and perform the needed functionality. Then a
measuring system can define the deviations between the build versus the
designed form or define the modifications needed to perform the needed
functionality.
For simple parts, a CMM is a good solution. If the part is complex, with
free forms, warped or bended, a scanner is usually preferred to understand
the problem (3D color plot with selected deviation flags) and get it fixed.
Then depending on the selected measuring technique, the specific
preparations have to be done to get data fast and in good quality (e.g.
built a fixturing for the part on a CMM or dull shiny or transparent parts
for scanning).
I do not fully agree with the statement: "it depends on the tolerance", it
depends much more on the part, the available time and the application.
We wish you a happy new year, with best regards
Ernst Müller www.gom.com
GOM International AG e.mueller@gom.com
Bremgarterstr. 89b Tel. ++41 56 631 04 04
CH - 8967 Widen, Switzerland Fax:++41 56 631 04 07
Anshuman Razdan
<Razdan@asu.edu>
Sent by: To
owner-rp-ml@rapid Marshall Burns
.lpt.fi <MB-ListMail2@Ennex.com>, "Good,
Jim" <Jim.Good@tbe.com>,
rp-ml@rapid.lpt.fi
28.12.2004 05:48 cc
Subject
RE: [rp-ml] FW: Geometric Accuracy
of RP parts
It depends on the tolerance. Laser is good, but requires dull surfaces for
best results. Any sharp angles or shiny metal will throw it off. There are
other metrology techniques but they are not fast. Speed vs accuracy is the
age old problem.
AR
-----Original Message-----
From: owner-rp-ml@rapid.lpt.fi [mailto:owner-rp-ml@rapid.lpt.fi] On
Behalf Of Marshall Burns
Sent: Monday, December 27, 2004 7:57 PM
To: 'Good, Jim'; rp-ml@rapid.lpt.fi
Subject: RE: [rp-ml] FW: Geometric Accuracy of RP parts
Jim,
This is a very important idea you're looking into. I don't have
specific recommendations of scanners for you, but just thought I'd
chime in about the concept. Even in a terrestrial application, it's
this kind of thing that will provide the feedback to ensure that a
fabber is on track, and let it make mid-course corrections. It's
obviously that much more critical in a remote application, like
space.
I'd be interested to learn more about your project as it
progresses.
Best regards,
Marshall Burns
www.fabbers.com
-----Original Message-----
From: owner-rp-ml@rapid.lpt.fi [mailto:owner-rp-ml@rapid.lpt.fi] On
Behalf Of Good, Jim
Sent: Monday, December 20, 2004 13:45
To: rp-ml@rapid.lpt.fi
Subject: [rp-ml] FW: Geometric Accuracy of RP parts
I thought I would throw this out. I am looking into inspection
equipment that will verify the geometric accuracy of my RP part,
after fabrication, and actually during fabrication. I’ve looked at
laser scanning and got some good input already. I’d like everyone’s
opinion on what system they are using and what they believe to be the
best system to verify geometric accuracy. The ultimate goal is to
build a fabricator that contains an integral inspection station.
This system would be used in space for repair and fabrication of new
parts. Any thoughts?
Thanks,
Jim Good
Muniz Engineering Inc.
In Situ Fabrication and Repair (ISFR)
256-726-1199
jim.good@tbe.com
Received on Tue Dec 28 12:47:00 2004
This archive was generated by hypermail 2.1.8 : Tue Jan 12 2010 - 19:37:12 EET